Difference between revisions of "Template:Announcements"

Latest revision as of 12:20, 27 September 2024

MLA Service this Tuesday

HIMT will be onsite around 9am this Tuesday to address a minor issue with the tool. I have the blocked out until 5 pm but we do not anticipate it taking that long, hopefully about 4-5 hours. I'll send out an email once the tool is available.

-Lee //Vraj Mehalana 12:20, 27 September 2024 (PDT)

DSE is UP

I’ve completed the installation of the new spool and lamps and the tool is free to use. We’ve run a number of different etches and upon initial inspection everything looks normal. However, it’s recommended you start with a test etch in case there is a slight shift in process.

Thanks, Aidan // Demis D. John 12:36, 20 September 2024 (PDT)

Suss SB6-8E

When the vendor came in to install the new top heater he wasn't able to get the z-axis (elevator motor) to move. He was able to install the new heater and do a PM on the rest of the tool. We are ordering a new z-axis controller on the recommendation of the vendor. If all goes well this should solve the issue and make the bonder fully operational. I'll send out an email once the new controller has been installed.

-Aidan //Vraj Mehalana 12:43, 3 September 2024 (PDT)

YES is available

The error has been cleared and I ran a shorter 5 minute recipe with no warning/error.

This seems to be exclusive to the longer (8+ minute recipes), which are throwing warnings for every wafer run this long. It also appears that running 3 wafers on a longer recipe will result in an error and aborted run on the 3rd wafer. We are just going to have to live with this until we have our other generator back. So until then, please limit the longer runs to 2 wafers max. If you have more than 2 wafers to run on a longer recipe then wait about 5-10 minutes in between batches.

// Vraj Mehalana 14:16, 18 September 2024 (PDT)

ICP1 Down

The board we were waiting on arrived, but it did not resolve the tool issue. We are working with Panasonic on the next steps. //Vraj Mehalana 14:17, 1 March 2024 (PST)

Lab Access Changes: Symmetry App

The iris scanner has been decommissioned. Please use the card reader which supports:

-Physical card

-Mobile phone via Symmetry App

//Vraj Mehalana 16:59, 14 June 2024 (PDT)

@@ Line 1: / Line 1: @@
 <startfeed />
+=====MLA Service this Tuesday=====
-<!--feedBurner name="UCSBNanofab-Announcements" /-->
+HIMT will be onsite around 9am this Tuesday to address a minor issue with the tool. I have the blocked out until 5 pm but we do not anticipate it taking that long, hopefully about 4-5 hours. I'll send out an email once the tool is available.
-<!-- Description of the RSS feed -->
-'''''Important Announcements'''''
-----
-<!--
-SEE THE BOTTOM OF THIS PAGE FOR DETAILED INSTRUCTIONS ON ADDING NEWS ITEMS.
+-Lee
-In order for your post to show up correctly, you need to:
+//[[User:Mehalana v|Vraj Mehalana]] 12:20, 27 September 2024 (PDT)
->> Use FIVE equal-signs for the Title's heading level.  eg.: ===== my post =====
->> Use two slashes // and FOUR tilde's to insert your signature at the end of your post: //~~~~
--->
-<!---------------------------------------------->
-<!------------- Equipment Status ---------------->
-===== Nanofab Open =====
+=====DSE is UP=====
+I’ve completed the installation of the new spool and lamps and the tool is free to use.  We’ve run a number of different etches and upon initial inspection everything looks normal.  However, it’s recommended you start with a test etch in case there is a slight shift in process.
-Thank you for your patience during this annual shutdown. We got a lot accomplished. The lab is now open for use.
+Thanks, Aidan
-Please remember to pick up your name tag from the table and sign for your hangar spot.
+// [[User:John_d|Demis D. John]] 12:36, 20 September 2024 (PDT)
-Also, Any personal items left on the hangars should be in the box in the lobby.
+=====Suss SB6-8E=====
-// [[User:John d|John d]] 10:05, 31 December 2022 (PST)
+When the vendor came in to install the new top heater he wasn't able to get the z-axis (elevator motor) to move.  He was able to install the new heater and do a PM on the rest of the tool.  We are ordering a new z-axis controller on the recommendation of the vendor.  If all goes well this should solve the issue and make the bonder fully operational.  I'll send out an email once the new controller has been installed.
-===== Au Plating: DOWN =====
-Bath damaged, system is down for repair.
-// [[User:John d|John d]] 08:48, 27 October 2022 (PDT)
+-Aidan
-<!---------- end of Equipment Status ------------>
+//[[User:Mehalana v|Vraj Mehalana]] 12:43, 3 September 2024 (PDT)
-<!---------------------------------------------->
-<endfeed />
-<noinclude>[[Category:Templates]]</noinclude>
-<!--------------------------------------------
+=====YES is available=====
+The error has been cleared and I ran a shorter 5 minute recipe with no warning/error.
+This seems to be exclusive to the longer (8+ minute recipes), which are throwing warnings for every wafer run this long. It also appears that running 3 wafers on a longer recipe will result in an error and aborted run on the 3rd wafer. We are just going to have to live with this until we have our other generator back. So until then, please limit the longer runs to 2 wafers max. If you have more than 2 wafers to run on a longer recipe then wait about 5-10 minutes in between batches.
+// [[User:Mehalana v|Vraj Mehalana]] 14:16, 18 September 2024 (PDT)
-====== HOW TO ADD ITEMS ======
+=====ICP1 Down=====
+The board we were waiting on arrived, but it did not resolve the tool issue. We are working with Panasonic on the next steps.
+//[[User:Mehalana v|Vraj Mehalana]] 14:17, 1 March 2024 (PST)
+=====Lab Access Changes: Symmetry App=====
+The iris scanner has been decommissioned. Please use the card reader which supports:
+-Physical card
+-Mobile phone via Symmetry App
+//[[User:Mehalana v|Vraj Mehalana]] 16:59, 14 June 2024 (PDT)
+<!--
+SEE THE BOTTOM OF THIS PAGE FOR DETAILED INSTRUCTIONS ON ADDING NEWS ITEMS.
+In order for your post to show up correctly, you need to:
+>> Use FIVE equal-signs for the Title's heading level.  eg.: ===== my post =====
+>> Use two slashes // and FOUR tilde's to insert your signature at the end of your post: //~~~~
+-->
+<!---------DO NOT EDIT BELOW THIS LINE----------->
+<endfeed />
+<noinclude>[[Category:Templates]]</noinclude>
+<!--------------------------------------------
+====== HOW TO ADD ITEMS ======
 * You can copy/paste the example below for a new news item.
 * Use level 5 heading for each item (5 equal signs surrounding the title) - they will show up as separate RSS items this way.  (This looks best on the Wiki homepage)
-* You must add a user signature at the end of each post via four tildes: ~~~~. Required for the RSS plugin to determine the timestamp, or else post goes to the end of the RSS feed.
+* You must add a user signature at the end of each post via four tildes: [[User:Silva|Silva]] 13:26, 4 February 2023 (PST). Required for the RSS plugin to determine the timestamp, or else post goes to the end of the RSS feed.
 * Use double-slash:   //   at start of new lines - makes display on the Samsung Display look a lot better, since it strips newlines.
 * Optional: After saving the page, delete the name after the two dashes "--" and delete the "[[(talk)...]]" link.
@@ Line 51: / Line 64: @@
 ===== NanoFab making LN2 icecream =====
 Tomorrow the NanoFab will be serving liquid nitrogen ice cream.
+// [[User:Silva|Silva]] 13:26, 4 February 2023 (PST)
-// ~~~~
 ************* (end of example) **************
-The ~~~~ will be replaced with your username & timestamp after you submit the post.
+The [[User:Silva|Silva]] 13:26, 4 February 2023 (PST) will be replaced with your username & timestamp after you submit the post.
 ---------------------------------------------->