Difference between revisions of "Template:Announcements"

Latest revision as of 10:36, 30 May 2024

EBeam4 Update - Still down

EBeam4 will remain down overnight.

The new motor arrived as well as the new junction box and new cables.

I removed the old junction box/plugs due to a lot of corrosion inside the box caused by it being located directly under the water supply lines.

This corrosion inside the box could have contributed to the failure of the old motor.

I installed the new motor, ran all new cables to the new junction box in it's new location away from the water lines.

I was able to test the function of the hoist by raising and lowering the bell jar while in manual mode.

For safety reasons, I had the machine powered off during the duration of the work being done, so the cryo will be in regen overnight.

Tomorrow morning I will continue testing the system to ensure everything is working properly before I release the tool.

I will send another email when an update is available.

//10:36, 30 May 2024 (PDT)

Stepper #3 (ASML DUV) - System UP and calibrated

We have finished calibrations, System is up.

Reminder to check/recalibrate your exposure dose. Focus should be the same, but beam optics changeout will affect dose.

//Vraj Mehalana 11:17, 24 May 2024 (PDT)

Atomic Force Microscope (Dimension ICON) - 05/17: System UP

Head was repaired and returned today. A quick test showed correct performance. Note also that the pin board has been repaired so all 4 pins are now present. Lets keep it that way so please be careful when loading the tip holder!

//Vraj Mehalana 13:46, 20 May 2024 (PDT)

MA6 TSA is down - Update

We have received the replacement motor for the TSA Y axis. The FSE will be onsite Monday June 3rd to work on the tool.

The tool remains up for backside alignment and topside exposures that do not require alignment.

-Lee //15:59, 22 May 2024 (PDT)

Velion FIB Tool DOWN

Raith service are installing and aligning a new GaBiLi source. The Velion FIB column is not available to users until further notice.

//Vraj Mehalana 10:58, 30 April 2024 (PDT)

ICP1 Down

The board we were waiting on arrived, but it did not resolve the tool issue. We are working with Panasonic on the next steps. //Vraj Mehalana 14:17, 1 March 2024 (PST)

Lab Access Changes: Symmetry App

The iris scanner has been decommissioned. Please use the card reader which supports:

-Physical card

-Mobile phone via Symmetry App

//10:54, 23 May 2024 (PDT)

Wafer Bonder, (Suss SB6-8E)

SUSS aims to be on site in early February. We’ll will send out an email once I get confirmation for a specific date. //Vraj Mehalana 14:23, 13 December 2023 (PST)

@@ Line 1: / Line 1: @@
 <startfeed />
+=====EBeam4 Update - Still down=====
-<!--feedBurner name="UCSBNanofab-Announcements" /-->
+EBeam4 will remain down overnight.
-<!-- Description of the RSS feed -->
-'''''Important Announcements'''''
-----
-<!--
-SEE THE BOTTOM OF THIS PAGE FOR DETAILED INSTRUCTIONS ON ADDING NEWS ITEMS.
+The new motor arrived as well as the new junction box and new cables.
-In order for your post to show up correctly, you need to:
->> Use FIVE equal-signs for the Title's heading level.  eg.: ===== my post =====
->> Use two slashes // and FOUR tilde's to insert your signature at the end of your post: //~~~~
--->
-<!---------------------------------------------->
-<!------------- Equipment Status ---------------->
+I removed the old junction box/plugs due to a lot of corrosion inside the box caused by it being located directly under the water supply lines.
-===== Oxford ICP Installed =====
-A new ICP etcher for III-V etches (GaAs, InP, GaN) has been installed: [[Oxford_ICP_Etcher_(PlasmaPro_100_Cobra)]]
+This corrosion inside the box could have contributed to the failure of the old motor.
-Contact [[Tony_Bosch | the supervisor]] for training.
-// [[User:John d|John d]] 08:00, 30 September 2021 (PDT)
+I installed the new motor, ran all new cables to the new junction box in it's new location away from the water lines.
+I was able to test the function of the hoist by raising and lowering the bell jar while in manual mode.
-===== New UC system-wide Flu Vaccine mandate  =====
-The UC Office of the President has issued an executive order making influenza vaccinations mandatory for all UC students and employees. The order, effective throughout the 2021-22 flu season, requires that all students and faculty and staff members who live, learn or work on any UC campus or want to access any UC facilities attest that they have received a flu vaccination, or have chosen to decline a vaccination, no later than November 19.  Declining the vaccination will require use of masks indoors throughout the flu season.
+For safety reasons, I had the machine powered off during the duration of the work being done, so the cryo will be in regen overnight.
-All facility users are covered under this mandate.
-//[[User:Thibeault|Thibeault]] 11:26, 27 October 2021 (PDT)
+Tomorrow morning I will continue testing the system to ensure everything is working properly before I release the tool.
-===== New COVID Protocols =====
-All facility users and visitors are now required to have masks on while indoors in shared spaces.  This includes shared offices, hallways/corridors, and all shared laboratory spaces.  Masks will be worn in all laboratories at all times and in all shared office spaces at all times.
+I will send another email when an update is available.
-This direction applies to all vaccinated and non-vaccinated persons.
+//10:36, 30 May 2024 (PDT)
-Outdoor policies remain unchanged
+=====Stepper #3 (ASML DUV) - System UP and calibrated=====
-Surgical style masks or KN95 masks are appropriate for cleanroom use.  Cloth masks may be used in non-cleanroom spaces.
+We have finished calibrations,
+System is up.
+Reminder to check/recalibrate your exposure dose. Focus should be the same, but beam optics changeout will affect dose.
-See the full policies at [[COVID-19_User_Policies]]
-// [[User:Hopkins a|Hopkins a]] 08:14, 6 August 2021 (PDT)
+//[[User:Mehalana v|Vraj Mehalana]] 11:17, 24 May 2024 (PDT)
-===== Weekly Testing strongly urged for UCSB Students/Staff =====
+=====Atomic Force Microscope (Dimension ICON) - 05/17: System UP=====
+Head was repaired and returned today.  A quick test showed correct performance.  Note also that the pin board has been repaired so all 4 pins are now present.  Lets keep it that way so please be careful when loading the tip holder!
-Free weekly COVID testing is available to UCSB Staff, Faculty and Students. UCSB employees are strongly urged to sign up for weekly testing, which takes only minutes, is administered on-campus and is free of charge.
+//[[User:Mehalana v|Vraj Mehalana]] 13:46, 20 May 2024 (PDT)
-Weekly recurring appointments can be made at the Student Health website:
-* Log on to the [https://studenthealthoc.sa.ucsb.edu/login_dualauthentication.aspx '''UCSB Testing Patient Portal'''] using your UCSB NetID and password.
+=====MA6 TSA is down - Update=====
-The Chancellor's [https://chancellor.ucsb.edu/memos/2020-10-15-recommended-covid-19-asymptomatic-campus-testing-program-faculty-staff-and memo to campus with details can be found here].
+We have received the replacement motor for the TSA Y axis. The FSE will be onsite Monday June 3rd to work on the tool.
-// [[User:John d|John d]] 06:20, 16 November 2020 (PST)
+The tool remains up for backside alignment and topside exposures that do not require alignment.
-===== NanoFab COVID Protocols =====
+-Lee
-''The most recent COVID Protocols can be found at '''[[COVID-19_User_Policies]]'''.''
+//15:59, 22 May 2024 (PDT)
+=====Velion FIB Tool DOWN=====
-// [[User:John d|John d]] 15:00, 19 July 2020 (PDT)
+Raith service are installing and aligning a new GaBiLi source. The Velion FIB column is not available to users until further notice.
+//[[User:Mehalana v|Vraj Mehalana]] 10:58, 30 April 2024 (PDT)
+=====ICP1 Down=====
-<!---------- end of Equipment Status ------------>
+The board we were waiting on arrived, but it did not resolve the tool issue. We are working with Panasonic on the next steps.
-<!---------------------------------------------->
+//[[User:Mehalana v|Vraj Mehalana]] 14:17, 1 March 2024 (PST)
-<endfeed />
-<noinclude>[[Category:Templates]]</noinclude>
-<!--------------------------------------------
+=====Lab Access Changes: Symmetry App=====
+The iris scanner has been decommissioned. Please use the card reader which supports:
+-Physical card
+-Mobile phone via Symmetry App
+//10:54, 23 May 2024 (PDT)
-====== HOW TO ADD NEWS ITEMS ======
+=====Wafer Bonder, (Suss SB6-8E)=====
+SUSS aims to be on site in early February.  We’ll will send out an email once I get confirmation for a specific date.
+//[[User:Mehalana v|Vraj Mehalana]] 14:23, 13 December 2023 (PST)
+<!--
+SEE THE BOTTOM OF THIS PAGE FOR DETAILED INSTRUCTIONS ON ADDING NEWS ITEMS.
+In order for your post to show up correctly, you need to:
+>> Use FIVE equal-signs for the Title's heading level.  eg.: ===== my post =====
+>> Use two slashes // and FOUR tilde's to insert your signature at the end of your post: //~~~~
+-->
+<!---------DO NOT EDIT BELOW THIS LINE----------->
+<endfeed />
+<noinclude>[[Category:Templates]]</noinclude>
+<!--------------------------------------------
+====== HOW TO ADD ITEMS ======
 * You can copy/paste the example below for a new news item.
 * Use level 5 heading for each item (5 equal signs surrounding the title) - they will show up as separate RSS items this way.  (This looks best on the Wiki homepage)
-* You must add a user signature at the end of each post via four tildes: ~~~~. Required for the RSS plugin to determine the timestamp, or else post goes to the end of the RSS feed.
+* You must add a user signature at the end of each post via four tildes: [[User:Silva|Silva]] 13:26, 4 February 2023 (PST). Required for the RSS plugin to determine the timestamp, or else post goes to the end of the RSS feed.
 * Use double-slash:   //   at start of new lines - makes display on the Samsung Display look a lot better, since it strips newlines.
 * Optional: After saving the page, delete the name after the two dashes "--" and delete the "[[(talk)...]]" link.
 * Please use "There are no announcements at this time." if the announcements are empty.
-* URL to the RSS feed via FeedBurner (for Samsung display): http://feeds.feedburner.com/UCSBNanofab-Announcements?format=xml
+* URL to the RSS feed via FeedBurner (for Samsung display): http://wiki.nanotech.ucsb.edu/w/index.php?title=Template:Announcements&action=feed&feed=rss
-* URL to the RSS feed directly from Wiki: https://www.nanotech.ucsb.edu/wiki/index.php?title=Template:Announcements&action=feed&feed=rss
+* URL to the RSS feed directly from Wiki: https://wiki.nanotech.ucsb.edu/w/index.php?title=Template:Announcements&action=feed&feed=rss
@@ Line 82: / Line 90: @@
 ===== NanoFab making LN2 icecream =====
 Tomorrow the NanoFab will be serving liquid nitrogen ice cream.
+// [[User:Silva|Silva]] 13:26, 4 February 2023 (PST)
-// ~~~~
 ************* (end of example) **************
-The ~~~~ will be replaced with your username & timestamp after you submit the post.
+The [[User:Silva|Silva]] 13:26, 4 February 2023 (PST) will be replaced with your username & timestamp after you submit the post.
 ---------------------------------------------->