Contact Alignment Recipes
Back to Lithography Recipes.
Notes
Below is a listing of contact lithography recipes for use with designated aligners. Based on your sample reflectivity, absorption, and surface topography the exposure time parameters may vary. This listing is a guideline to get you started. The recipes are tabulated to give you the values of the key parameters you will need to establish your recipe. For best resolution using thin resists, you will need to remove any edge bead before contact and exposure. Also, hard contact mode will give you the most intimate contact between sample and mask, giving the best resolution. Post develop bakes (not listed) are used to make the resist more etch resistant and depend on subsequent processes. Unless otherwise noted, all exposures are done on silicon wafers.
Suss Aligners (SUSS MJB-3)
Positive Resist (MJB-3)
Unless otherwise noted, bakes are on hot plates and the exposure of the resist is done using no filtering at 7.5 mW/cm2. Power of the lamp is set using the 405 nm (h-line) detector.
| Resist | Spin Cond. | Bake | Thickness | Exposure Time | Developer | Developer Time | Comments |
|---|---|---|---|---|---|---|---|
| AZ4110 | 4 krpm/30” | 95°C/60” | ~ 1.1 um | 8” | AZ400K:DI 1:4 | 50" | |
| AZ4210 | 4 krpm/30” | 95°C/60” | ~ 2.1 um | 13” | AZ400K:DI 1:4 | 70” | |
| AZ4330 | 4 krpm/30” | 95°C/60” | ~ 3.3 um | 18” | AZ400K:DI 1:4 | 90” | |
| SPR220-3.0 | 3.5 krpm/30” | 115°C/90” | ~ 2.5 um | 25” | AZ300MIF | 50” |
|
| SPR220-7.0 | 3.5 krpm/45” | 115°C/120” | ~ 7.5 um | 60” | AZ300MIF | 70” |
Negative Resist (MJB-3)
Unless otherwise noted, bakes are on hot plates and the exposure of the resist is done using no filtering at 7.5 mW/cm2. Power of the lamp is set using the 405 nm (h-line) detector. In general, many negative resists require post-exposure-bakes (PEB) / flood exposures in order to make the negative tone of the image. All flood exposures are done in broadband light using any contact aligner. Also, because the tone is negative, a shorter first exposure time will result in more undercut, which is desirable for single-layer lift-off processes. Under these conditions more develop time will also give more undercut.
| Resist | Spin Cond. | Bake | Thickness | Exposure Time | PEB | Flood | Developer | Developer Time | Comments |
|---|---|---|---|---|---|---|---|---|---|
| AZ5214 | 6 krpm/30” | 95°C/60” | ~ 1 um | 5” | 110°C/60” | 60” | AZ400K:DI 1:5.5 or AZ300MIF |
60" 45" |
|
| AZ5214 | 6 krpm/30” | 95°C/60” | ~ 1 um | 10” | 110°C/60” | 60” | AZ300MIF | 45” |
|
| AZnLOF2020 | 3 krpm/30” | 110°C/90” | ~ 2.1 um | 10” | 110°C/60” | AZ300MIF | 60” |
|
Contact Aligner (SUSS MA-6)
| To Do: Have Brian double check the exposure times. |
| To Do: Are the "more information" sheets valid for both tools? |
Positive Resist (MA-6)
Unless otherwise noted, bakes are on hot plates and the exposure of the resist is done using no filtering at 7.5 mW/cm2. Power of the lamp is set using the 405 nm (h-line) detector. For the MA-6 aligner, using Channel 1, the exposure times given below are the same as the MJB-3 except reduced by a factor of 2.4.
| Resist | Spin Cond. | Bake | Thickness | Exposure Time | Developer | Developer Time | Comments | ||||||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| AZ4110 | 4 krpm/30” | 95°C/60” | ~ 1.1 um | 3.3” | AZ400K:DI 1:4 | 50" | |||||||||||||||||||||||||||||||||||||||||
| AZ4210 | 4 krpm/30” | 95°C/60” | ~ 2.1 um | 5.4” | AZ400K:DI 1:4 | 70” | |||||||||||||||||||||||||||||||||||||||||
| AZ4330 | 4 krpm/30” | 95°C/60” | ~ 3.3 um | 7.5” | AZ400K:DI 1:4 | 90” | |||||||||||||||||||||||||||||||||||||||||
| SPR220-3.0 | 3.5 krpm/30” | 115°C/90” | ~ 2.5 um | 10.4” | AZ300MIF | 50” |
| ||||||||||||||||||||||||||||||||||||||||
| SPR220-7.0 | 3.5 krpm/45” | 115°C/120” | ~ 7.5 um | 25” | AZ300MIF | 70” |
Negative Resist (MA-6)Unless otherwise noted, bakes are on hot plates and the exposure of the resist is done using no filtering at 7.5 mW/cm2. Power of the lamp is set using the 405 nm (h-line) detector. In general, many negative resists require post-exposure-bakes (PEB) / flood exposures in order to make the negative tone of the image. All flood exposures are done in broadband light using any contact aligner. Also, because the tone is negative, a shorter first exposure time will result in more undercut, which is desirable for single-layer lift-off processes. Under these conditions more develop time will also give more undercut. For the MA-6 aligner, using Channel 1, the exposure times given below are the same as the MJB-3 except reduced by a factor of 2.4.
|