Difference between revisions of "Template:Announcements"

Latest revision as of 14:41, 13 May 2024

Atomic Force Microscope (Dimension ICON) - 05/08: AFM Head needs repair

I will have to take the AFM head unit back to Bruker for repair. The height sensor failed all the tests I tried so the Z-piezo/strain gauge unit will most likely need to be replaced. SO for the foreseeable future, the AFM is down.--Demis

//Vraj Mehalana 13:42, 9 May 2024 (PDT)

MA6 TSA is down - Update

After working with our FSE over the phone, we feel the culprit is a bound up Y axis motor for the top side microscope. Unfortunately, this axis is at the bottom of the microscope assembly and will require the removal of both the X and Z axis sub assemblies. I am awaiting proper instructions on how to dismantle all of this and the FSE is also checking with some of their contacts to see if there is an easier solution.

I have been asked by a few users about using the tool in TSA mode for exposures that do not require alignment even through the topside microscope is not functional. I have just tested the tool in TSA mode and it will work like this, just note that the topside microscope will not come down.

-Lee

//Vraj Mehalana 14:41, 13 May 2024 (PDT)

Velion FIB Tool DOWN

Raith service are installing and aligning a new GaBiLi source. The Velion FIB column is not available to users until further notice.

//Vraj Mehalana 10:58, 30 April 2024 (PDT)

ASML optics replacement May 20th-22nd

We will be performing beam delivery optics replacement on Mon May 20th to 22nd, to resolve a low intensity reading. The tool will be unavailable during this time.e.

//Vraj Mehalana 09:40, 9 May 2024 (PDT)

ICP1 Down

The board we were waiting on arrived, but it did not resolve the tool issue. We are working with Panasonic on the next steps. //Vraj Mehalana 14:17, 1 March 2024 (PST)

Lab Access Changes: Symmetry App

Card/Iris scanner access is still currently enabled. However we will be moving to a smartphone-based access system. IMPORTANT: check your email to setup the new smartphone access system, so you will be ready when we switch to the new system. Look for an email titled "Invitation to Access Symmetry App". // John d 13:49, 7 November 2023 (PST)

Wafer Bonder, (Suss SB6-8E)

SUSS aims to be on site in early February. We’ll will send out an email once I get confirmation for a specific date. //Vraj Mehalana 14:23, 13 December 2023 (PST)

@@ Line 1: / Line 1: @@
 <startfeed />
+=====Atomic Force Microscope (Dimension ICON) - 05/08: AFM Head needs repair=====
-<!--feedBurner name="UCSBNanofab-Announcements" /-->
+I will have to take the AFM head unit back to Bruker for repair. The height sensor failed all the tests I tried so the Z-piezo/strain gauge unit will most likely need to be replaced.  SO for the foreseeable future, the AFM is down.--Demis
-<!-- Description of the RSS feed -->
-''UCSB NanoFab Announcements''
-<!--
-'''How to add new news items'''
+//[[User:Mehalana v|Vraj Mehalana]] 13:42, 9 May 2024 (PDT)
-* Use level 5 heading for each item (5 equal signs) - they will show up as separate RSS items this way.  (looks best on the Wiki homepage)
+=====MA6 TSA is down - Update=====
-* You must add a user signature at the end of each post via four tildes: ~~~~. Required for the RSS plugin to determine the timestamp, or else post goes to the end of the RSS feed.
+After working with our FSE over the phone, we feel the culprit is a bound up Y axis motor for the top side microscope. Unfortunately, this axis is at the bottom of the microscope assembly and will require the removal of both the X and Z axis sub assemblies. I am awaiting proper instructions on how to dismantle all of this and the FSE is also checking with some of their contacts to see if there is an easier solution.
-* Use double-slash:   //   at start of new lines - makes display on the Samsung Display look a lot better, since it strips newlines.
-* Optional: After saving the page, delete the name after the two dashes "--" and delete the "[[(talk)...]]" link.
-* "There are no announcements at this time." should be used when empty.
+I have been asked by a few users about using the tool in TSA mode for exposures that do not require alignment even through the topside microscope is not functional. I have just tested the tool in TSA mode and it will work like this, just note that the topside microscope will not come down.
-Example of a new post:
+-Lee
-===== NanoFab making LN2 icecream =====
-Tomorrow the NanoFab will be serving liquid nitrogen ice cream.
-// ~~~~
+//[[User:Mehalana v|Vraj Mehalana]] 14:41, 13 May 2024 (PDT)
-(end of example)
-The ~~~~ will be replaced with your username & timestamp after you submit the post.
+=====Velion FIB Tool DOWN=====
--->
+Raith service are installing and aligning a new GaBiLi source. The Velion FIB column is not available to users until further notice.
-<!---------------------------------------------->
-<!------------- Announcements ---------------->
-===== Stepper #2 AutoStep: UP =====
-One RMS motor and motor control board was replaced. I ran setup
-without error. The system is up and ready for your use.
-// [[User:John d|John d]] 12:50, 25 April 2018 (PDT)
+//[[User:Mehalana v|Vraj Mehalana]] 10:58, 30 April 2024 (PDT)
-===== PECVD#2 Upgrades in progress, Retraining required =====
-Plasmatherm is still upgrading the system software. The user interface will be completely different from the previous software, so all users will be disqualified and will need to be retrained to access the system through Signupmonkey. We will schedule training sessions once the upgrade is complete.
-// [[User:John d|John d]] 12:51, 24 April 2018 (PDT)
-===== RIE#5 Up, SiCl4 unavailable =====
+=====ASML optics replacement May 20th-22nd=====
+We will be performing beam delivery optics replacement on Mon May 20th to 22nd, to resolve a low intensity reading. The tool will be unavailable during this time.e.
-The SiCl4 gas line is down until next week when we can change the gas
-panel.
-// [[User:John d|John d]] 16:15, 26 April 2018 (PDT)
+//[[User:Mehalana v|Vraj Mehalana]] 09:40, 9 May 2024 (PDT)
-===== Cary 500 Down =====
-UV-Vis Detector Failure. Tool is able to used from 600nm and up. Looking into replacement options.
-// [[User:John d|Posted:]] 13:47, 12 February 2018 (PST)
+=====ICP1 Down=====
-<!---------- end of announcements ------------>
+The board we were waiting on arrived, but it did not resolve the tool issue. We are working with Panasonic on the next steps.
-<!---------------------------------------------->
+//[[User:Mehalana v|Vraj Mehalana]] 14:17, 1 March 2024 (PST)
+=====Lab Access Changes: Symmetry App=====
+Card/Iris scanner access is still currently enabled.  However we will be moving to a smartphone-based access system.  '''IMPORTANT''': check your email to setup the new smartphone access system, so you will be ready when we switch to the new system. Look for an email titled '''''"Invitation to Access Symmetry App"'''''.
+// [[User:John d|John d]] 13:49, 7 November 2023 (PST)
+=====Wafer Bonder, (Suss SB6-8E)=====
+SUSS aims to be on site in early February.  We’ll will send out an email once I get confirmation for a specific date.
+//[[User:Mehalana v|Vraj Mehalana]] 14:23, 13 December 2023 (PST)
+<!--
+SEE THE BOTTOM OF THIS PAGE FOR DETAILED INSTRUCTIONS ON ADDING NEWS ITEMS.
+In order for your post to show up correctly, you need to:
+>> Use FIVE equal-signs for the Title's heading level.  eg.: ===== my post =====
+>> Use two slashes // and FOUR tilde's to insert your signature at the end of your post: //~~~~
+-->
+<!---------DO NOT EDIT BELOW THIS LINE----------->
 <endfeed />
 <noinclude>[[Category:Templates]]</noinclude>
+<!--------------------------------------------
+====== HOW TO ADD ITEMS ======
+* You can copy/paste the example below for a new news item.
+* Use level 5 heading for each item (5 equal signs surrounding the title) - they will show up as separate RSS items this way.  (This looks best on the Wiki homepage)
+* You must add a user signature at the end of each post via four tildes: [[User:Silva|Silva]] 13:26, 4 February 2023 (PST). Required for the RSS plugin to determine the timestamp, or else post goes to the end of the RSS feed.
+* Use double-slash:   //   at start of new lines - makes display on the Samsung Display look a lot better, since it strips newlines.
+* Optional: After saving the page, delete the name after the two dashes "--" and delete the "[[(talk)...]]" link.
+* Please use "There are no announcements at this time." if the announcements are empty.
+* URL to the RSS feed via FeedBurner (for Samsung display): http://wiki.nanotech.ucsb.edu/w/index.php?title=Template:Announcements&action=feed&feed=rss
+* URL to the RSS feed directly from Wiki: https://wiki.nanotech.ucsb.edu/w/index.php?title=Template:Announcements&action=feed&feed=rss
+******** EXAMPLE OF A NEW POST ********
+===== NanoFab making LN2 icecream =====
+Tomorrow the NanoFab will be serving liquid nitrogen ice cream.
+// [[User:Silva|Silva]] 13:26, 4 February 2023 (PST)
+************* (end of example) **************
+The [[User:Silva|Silva]] 13:26, 4 February 2023 (PST) will be replaced with your username & timestamp after you submit the post.
+---------------------------------------------->