Difference between revisions of "Template:Announcements"

Latest revision as of 14:41, 13 May 2024

Atomic Force Microscope (Dimension ICON) - 05/08: AFM Head needs repair

I will have to take the AFM head unit back to Bruker for repair. The height sensor failed all the tests I tried so the Z-piezo/strain gauge unit will most likely need to be replaced. SO for the foreseeable future, the AFM is down.--Demis

//Vraj Mehalana 13:42, 9 May 2024 (PDT)

MA6 TSA is down - Update

After working with our FSE over the phone, we feel the culprit is a bound up Y axis motor for the top side microscope. Unfortunately, this axis is at the bottom of the microscope assembly and will require the removal of both the X and Z axis sub assemblies. I am awaiting proper instructions on how to dismantle all of this and the FSE is also checking with some of their contacts to see if there is an easier solution.

I have been asked by a few users about using the tool in TSA mode for exposures that do not require alignment even through the topside microscope is not functional. I have just tested the tool in TSA mode and it will work like this, just note that the topside microscope will not come down.

-Lee

//Vraj Mehalana 14:41, 13 May 2024 (PDT)

Velion FIB Tool DOWN

Raith service are installing and aligning a new GaBiLi source. The Velion FIB column is not available to users until further notice.

//Vraj Mehalana 10:58, 30 April 2024 (PDT)

ASML optics replacement May 20th-22nd

We will be performing beam delivery optics replacement on Mon May 20th to 22nd, to resolve a low intensity reading. The tool will be unavailable during this time.e.

//Vraj Mehalana 09:40, 9 May 2024 (PDT)

ICP1 Down

The board we were waiting on arrived, but it did not resolve the tool issue. We are working with Panasonic on the next steps. //Vraj Mehalana 14:17, 1 March 2024 (PST)

Lab Access Changes: Symmetry App

Card/Iris scanner access is still currently enabled. However we will be moving to a smartphone-based access system. IMPORTANT: check your email to setup the new smartphone access system, so you will be ready when we switch to the new system. Look for an email titled "Invitation to Access Symmetry App". // John d 13:49, 7 November 2023 (PST)

Wafer Bonder, (Suss SB6-8E)

SUSS aims to be on site in early February. We’ll will send out an email once I get confirmation for a specific date. //Vraj Mehalana 14:23, 13 December 2023 (PST)

@@ Line 1: / Line 1: @@
 <startfeed />
+=====Atomic Force Microscope (Dimension ICON) - 05/08: AFM Head needs repair=====
-<!--feedBurner name="UCSBNanofab-Announcements" /-->
+I will have to take the AFM head unit back to Bruker for repair. The height sensor failed all the tests I tried so the Z-piezo/strain gauge unit will most likely need to be replaced.  SO for the foreseeable future, the AFM is down.--Demis
-<!-- Description of the RSS feed -->
-'''''Equipment Status'''''
-----
-<!--
-SEE THE BOTTOM OF THIS PAGE FOR INSTRUCTIONS ON ADDING NEWS ITEMS.
+//[[User:Mehalana v|Vraj Mehalana]] 13:42, 9 May 2024 (PDT)
-Please use FIVE equal-signs for the Title's heading level.  eg.: ===== my post =====
+=====MA6 TSA is down - Update=====
--->
+After working with our FSE over the phone, we feel the culprit is a bound up Y axis motor for the top side microscope. Unfortunately, this axis is at the bottom of the microscope assembly and will require the removal of both the X and Z axis sub assemblies. I am awaiting proper instructions on how to dismantle all of this and the FSE is also checking with some of their contacts to see if there is an easier solution.
-<!---------------------------------------------->
-<!------------- Equipment Status ---------------->
-===== UCSB Flu Vaccination Mandate =====
-UCSB Students, Staff and Faculty are required to recieve a Flu Vaccine by Nov. 1st. <br>Please see the '''[[COVID-19_User_Policies#UCSB_Flu_Vaccination_Mandate|COVID19 Page]]''' for relevant links and information.
-// [[User:John d|John d]] 19:47, 13 October 2020 (PDT)
+I have been asked by a few users about using the tool in TSA mode for exposures that do not require alignment even through the topside microscope is not functional. I have just tested the tool in TSA mode and it will work like this, just note that the topside microscope will not come down.
-===== NanoFab COVID Response =====
-Following guidelines provided by our Office of Research, the UCSB Nanofabrication Facility is open only for limited/authorized use for critical activity at this time.
+-Lee
-Contact the [[Brian Thibeault|Lab Director]] for more information.
-''The most recent COVID Protocols can be found at '''[[COVID-19_User_Policies]]'''.''
-// [[User:John d|John d]] 15:00, 19 July 2020 (PDT)
+//[[User:Mehalana v|Vraj Mehalana]] 14:41, 13 May 2024 (PDT)
-===== New Tool Installations =====
+=====Velion FIB Tool DOWN=====
+Raith service are installing and aligning a new GaBiLi source. The Velion FIB column is not available to users until further notice.
-See the [https://wiki.nanotech.ucsb.edu/w/index.php/Main_Page#mp-trivia-h2 News Feed] for info on two upcoming tool installations!  The [https://www.raith.com/products/velion.html?mobile=0 Raith Velion FIB] is up and running, we are eagerly awaiting Dr. Dan Read's arrival to bring this tool to life.  See the [[Focused_Ion-Beam_Lithography_(Raith_Velion)|Velion's Tool page here]].
+//[[User:Mehalana v|Vraj Mehalana]] 10:58, 30 April 2024 (PDT)
-The [https://heidelberg-instruments.com/en/products/mla150.html Heidelberg MLA150 Maskless Aligner] has been installed, and is in the process of being qualified/characterized.  See the [[Maskless_Aligner_(Heidelberg_MLA150)|MLA150's tool page here]].
+=====ASML optics replacement May 20th-22nd=====
-// [[User:John d|John d]] 17:48, 2 June 2020 (PDT)
+We will be performing beam delivery optics replacement on Mon May 20th to 22nd, to resolve a low intensity reading. The tool will be unavailable during this time.e.
+//[[User:Mehalana v|Vraj Mehalana]] 09:40, 9 May 2024 (PDT)
-===== Unaxis ICP-PECVD =====
-The ICP-PECVD module is available upon request.  Contact Tony Bosch if interested.  System is using deuterated Silane for low loss optical films use only.
+=====ICP1 Down=====
-// [[User:Thibeault|Thibeault]] 14:22, 26 March 2020 (PDT)
+The board we were waiting on arrived, but it did not resolve the tool issue. We are working with Panasonic on the next steps.
+//[[User:Mehalana v|Vraj Mehalana]] 14:17, 1 March 2024 (PST)
-===== GCA Autostep Maintenance =====
+=====Lab Access Changes: Symmetry App=====
+Card/Iris scanner access is still currently enabled.  However we will be moving to a smartphone-based access system.  '''IMPORTANT''': check your email to setup the new smartphone access system, so you will be ready when we switch to the new system. Look for an email titled '''''"Invitation to Access Symmetry App"'''''.
-C will be performing stepper maintenance starting the morning of October 23, 2020. The service will be completed in the afternoon Sunday October 25th. Please plan your process accordingly.
+// [[User:John d|John d]] 13:49, 7 November 2023 (PST)
+=====Wafer Bonder, (Suss SB6-8E)=====
-[[User:Silva|Silva]] 08:19, 23 October 2020 (PDT)
+SUSS aims to be on site in early February.  We’ll will send out an email once I get confirmation for a specific date.
+//[[User:Mehalana v|Vraj Mehalana]] 14:23, 13 December 2023 (PST)
+<!--
-===== GCA 6300 Maintenance =====
+SEE THE BOTTOM OF THIS PAGE FOR DETAILED INSTRUCTIONS ON ADDING NEWS ITEMS.
-The 6300 will be down the morning and afternoon Monday October 26, 2020 for maintenance. Please plan your process accordingly.
+In order for your post to show up correctly, you need to:
+>> Use FIVE equal-signs for the Title's heading level.  eg.: ===== my post =====
-[[User:Silva|Silva]] 08:19, 23 October 2020 (PDT)
+>> Use two slashes // and FOUR tilde's to insert your signature at the end of your post: //~~~~
+-->
+<!---------DO NOT EDIT BELOW THIS LINE----------->
-<!---------- end of Equipment Status ------------>
-<!---------------------------------------------->
 <endfeed />
 <noinclude>[[Category:Templates]]</noinclude>
 <!--------------------------------------------
+====== HOW TO ADD ITEMS ======
-====== HOW TO ADD NEWS ITEMS ======
 * You can copy/paste the example below for a new news item.
 * Use level 5 heading for each item (5 equal signs surrounding the title) - they will show up as separate RSS items this way.  (This looks best on the Wiki homepage)
-* You must add a user signature at the end of each post via four tildes: ~~~~. Required for the RSS plugin to determine the timestamp, or else post goes to the end of the RSS feed.
+* You must add a user signature at the end of each post via four tildes: [[User:Silva|Silva]] 13:26, 4 February 2023 (PST). Required for the RSS plugin to determine the timestamp, or else post goes to the end of the RSS feed.
 * Use double-slash:   //   at start of new lines - makes display on the Samsung Display look a lot better, since it strips newlines.
 * Optional: After saving the page, delete the name after the two dashes "--" and delete the "[[(talk)...]]" link.
 * Please use "There are no announcements at this time." if the announcements are empty.
-* URL to the RSS feed via FeedBurner (for Samsung display): http://feeds.feedburner.com/UCSBNanofab-Announcements?format=xml
+* URL to the RSS feed via FeedBurner (for Samsung display): http://wiki.nanotech.ucsb.edu/w/index.php?title=Template:Announcements&action=feed&feed=rss
-* URL to the RSS feed directly from Wiki: https://www.nanotech.ucsb.edu/wiki/index.php?title=Template:Announcements&action=feed&feed=rss
+* URL to the RSS feed directly from Wiki: https://wiki.nanotech.ucsb.edu/w/index.php?title=Template:Announcements&action=feed&feed=rss
@@ Line 75: / Line 63: @@
 ===== NanoFab making LN2 icecream =====
 Tomorrow the NanoFab will be serving liquid nitrogen ice cream.
+// [[User:Silva|Silva]] 13:26, 4 February 2023 (PST)
-// ~~~~
 ************* (end of example) **************
-The ~~~~ will be replaced with your username & timestamp after you submit the post.
+The [[User:Silva|Silva]] 13:26, 4 February 2023 (PST) will be replaced with your username & timestamp after you submit the post.
 ---------------------------------------------->