Pages with the fewest revisions

Showing below up to 50 results in range #1 to #50.

1. InP Etch Test-in details (1 revision)
2. TEST PAGE (1 revision)
3. Stepper 2 (AutoStep 200) - Operating Procedure - Piece Parts (1 revision)
4. AUTOSTEP 200-PIECES 1st litho BL and BR orientation.pptx (1 revision)
5. Surfscan Errors and Workarounds (1 revision)
6. Surfscan SOP for 6inch wafers (1 revision)
7. PECVD.docx (1 revision)
8. Operating Instructions (1 revision)
9. YES Recipe Screenshots: STD-N2-O2 (1 revision)
10. Publications - 2013-2014 (1 revision)
11. Advanced PECVD Recipes (1 revision)
12. PECVD1 Operating Instructions.pdf (1 revision)
13. Older Publications (1 revision)
14. Wafer coating procedure (1 revision)
15. UV Ozone Quick Start (1 revision)
16. RIE5 - Standard Operating procedure (Cortex Software) (1 revision)
17. UCSBTEST1Gain4.jpg (1 revision)
18. STD SiO2 recipe (1 revision)
19. Comparison of ash rate for different gas mixtures, especially between O2 only vs O2/N2 mixture. (1 revision)
20. LegacyTable (1 revision)
21. AUTOSTEP 200-PIECES instruction 6-20-19.pptx (1 revision)
22. ASML Stepper 3 - Substrates smaller than 100mm/4-inch (1 revision)
23. Surfscan SOP for 4inch wafers (1 revision)
24. MA6 Backside Alignment - Allowed Mark Locations (1 revision)
25. Unaxis SOP 3-12-2020.docx (1 revision)
26. Surfscan SOP for 8inch wafers (1 revision)
27. PECVD1-SiN-standard recipe.pdf (1 revision)
28. Unaxis Test Recipe Page (1 revision)
29. Filmetrics F50 - Operating Procedure (1 revision)
30. Oxford Etcher - Sample Size Effect on Etch Rate (1 revision)
31. SiN 100C Table-2019 (1 revision)
32. Stepper 1 (GCA6300) How to select proper chuck (1 revision)
33. Video Training - Introduction (Internal) (1 revision)
34. Lab Rules backup (1 revision)
35. Surfscan SOP for small substrates (1 revision)
36. Sputter 5 (1 revision)
37. Flood Exposure Recipes (1 revision)
38. ProcessGroup: Shipping Samples on Dicing Tape+Frame (1 revision)
39. Nanofab-IT - Add Device to Network (1 revision)
40. Stepper 1 (GCA 6300) Available chucks (1 revision)
41. Stepper 1 (GCA 6300) Substrate Thickness, Shim Thickness ans Target Thickness (1 revision)
42. Ellipsometer (Woollam) - Measuring thin dielectrics with Native Oxide pre-measurement (1 revision)
43. Quarter First Layer Instructions (1 revision)
44. Intellemetrics Laser Etch Monitor Procedure for Plasma-Therm Etchers (1 revision)
45. Equipment Group - Video Training Procedures (1 revision)
46. InP Etch test -details (1 revision)
47. YES Recipe Screenshots: STD-O2 (1 revision)
48. Research Pubs 2026-04-24 (1 revision)
49. Errors (2 revisions)
50. Silicon Deep Etcher (Plasma-Therm SLR) (2 revisions)